Driveway guide

Driveway lighting: what can go into a new drive, and what to plan first

A worker in protective gear laying paving stones on a wet day
Illustrative photograph, see credits.

Driveway lighting is one of those jobs that costs very little to plan in and a lot to add later. Once the surface is down, every cable means lifting blocks, cutting tarmac or living with a wire clipped along a wall. If you are having a new drive installed, the time to decide on lights is before the dig, not after. This guide covers the main types of driveway lighting, what each one asks of the build, and the questions to settle with your installer and your electrician. The guide to how long a new drive takes shows where in the job the ducting goes.

The main types of driveway lighting

  • Drive-over lights

    Small round lights set flush into the surface, usually along the edge or marking the line of the drive. They look clean, but they sit where tyres go, so they need to be rated to take a car's weight and sealed against standing water.

  • Bollard and post lights

    Low posts along the edge of the drive or a path. They light the ground well without glare, but they sit right where a car door opens or a bumper swings, so placement matters.

  • Wall lights

    Fitted to the house or a boundary wall. The simplest option, often wired from inside the house, and nothing sits in the drive itself.

  • Lights in walls and steps

    Small lights set into a retaining wall or step risers. Useful where a drive has a change of level next to a path.

  • Solar lights

    No cable at all. Fine as markers, but most give a soft glow rather than useful light, and they struggle through a dull UK winter.

What driveway lighting needs from the build

Any light set into or beside the drive needs a cable to reach it, and that cable should run in a duct buried in the sub-base, not loose in the bedding layer. The duct protects the cable from the compactor, from the next person who digs, and from the slow settling of the drive itself. Ask your installer to lay ducting with a draw string inside during the groundworks, with the ends marked, even if you are not buying the lights yet. A length of duct is cheap. Lifting a finished drive to add one is not.

Drive-over lights also need a solid, level housing so they sit flush and do not rock. On block paving they are usually set into cut blocks; on resin bound or tarmac they are fixed before the surface goes down, with the surface laid up to them. Either way the light becomes part of the surface, so the fitting has to be planned with the layout, not dropped in afterwards. Water is the other thing to plan for. A light set at the low point of a drive will sit in a puddle every time it rains, so agree the falls and the driveway drainage before you mark where the lights go.

Choosing fittings that last

Outdoor fittings carry an IP rating, two numbers that describe how well they keep out dust and water. For anything set into the ground, look for a rating that covers immersion, not just splashes, and for drive-over lights check the stated load rating as well. A light rated for a footpath is not rated for a car. Stainless steel or good quality aluminium bodies outlast cheap painted ones, which tend to blister after a few winters of road salt and pressure washing.

Low voltage systems, which run from a transformer near the house, are popular for drive and garden lighting because the cable running out to the lights carries a much lower voltage. Mains fittings give more choice of lights. Which suits your drive is a question for your electrician, not your paving crew.

Who wires it

In England, electrical work in homes falls under Part P of the Building Regulations, and adding a new circuit has to be done by an electrician registered with a competent person scheme, who can certify it, or notified to building control. Most driveway lighting needs a new circuit or an outdoor supply, so treat it as an electrician's job from the start. My team and I lay the ducting and set the housings where the electrician wants them; the electrician runs the cable, connects the lights and gives you the certificate. Getting both trades to agree the plan before the dig saves a return visit.

Getting the lighting right for the neighbours

A drive is lit to see the ground, the step and the car door, not to light the street. Point fittings down, use warm white rather than harsh cold light, and put the brighter lights on a sensor or timer rather than leaving them on all night. Bright lights shining into a neighbour's window cause more complaints than anything else about outdoor lighting, and they are easy to avoid at the planning stage.

Driveway lighting on an existing drive

If your drive is already down, wall lights are the easy win, because they need no digging at all. Edge lights can sometimes be added by lifting a single row of border blocks, running a duct and relaying them, which is far less disruptive than it sounds on a well built block drive. On tarmac, concrete or resin, adding cables means cutting a channel and patching it, and the patch will show. If the drive is near the end of its life anyway, the signs your driveway needs replacing are worth reading before you spend money on lights for it.

If you are planning a new drive, tell me about lighting when you ask for a quote. It changes almost nothing on the price at that stage, and the new driveway cost guide explains what does.

Written and reviewed by the PaveLocal team. We build and specify driveways across Northamptonshire, Buckinghamshire and Bedfordshire. Pricing and specification guidance on this page reflects what these jobs cost and involve in this region, not a national average.

Last reviewed: August 2026

Free quote

Get a free quote.

Postcode, rough size and a photo if you have one. Surveyed first, then an itemised written price.

  • Itemised, in writingExcavation, sub-base depth, edging, drainage and surface priced as separate lines, so you can compare quotes properly.
  • Surveyed before it is pricedGround conditions decide the cost of a driveway. Anyone quoting a firm price off a photo is guessing.
  • No obligationA quote is a quote. If you use someone else, that is fine, we will not chase you about it.

Prefer to talk it through? Call 07423 123796, message us on WhatsApp or email info@pavelocal.co.uk.

How should we get back to you?

No obligation and no hard sell. We use your details to quote your driveway and nothing else, see the privacy policy.